Nog wat info van analog hell:
Whole Mode
The MKS-7 has a "Whole Mode". The Melody and Chord sections are combined and act as a six voice synthesizer. In this mode there is no sound from the Melody Section. To turn on the Whole Mode, use the following procedure:
Press the MIDI CH button so the RHYTHM, BASS, CHORD and MELODY buttons are flashing.
While holding the CHORD button, press the MELODY button.
NOTE: The CHORD and MELODY indicators under the LED display should now both be lit.
Press the MIDI CH button to exit.
Entering engineer mode
While holding down one of the sound source selector buttons - MELODY, CHORD or BASS to be edited, depress the midi MIDI CH. The button flashes, indicating the machine is in engineering mode.
Editing
1: Using Tables 1 and 2, find out the number corresponding to a parameter to be altered. Eneter the number on the numerical pad. The display shows the number.
2: DYNAMIC SENS serves as an edit knob, and the new number is represented in the display window as a number between 00 and 127. The numbers above 100 are in lower two digits (eg 123 = 23) In the case where paramters functioning in place of switch, a parameter can effectively open or close the switch when the value exceeds the predetermined figure. For example, CHORUS is turned ON when the value decreases below 63, and OFF when above 64.
Returning to normal mode
Push the MIDI channel button to Normal Functioning.
TABLE 1 - MELODY and CHORD BLOCK PARAMETER
No. Parameter
01 LFO Rate
02 Delay time
03 DCO LFO Modulation
04 PWM
05 VCF Cutoff frequency
06 Resonance
07 ENV Modulation
08 LFO Modulation
09 Key follow
10 VCA Level
11 ENV Attack time
12 Decay time
13 Sustain time
14 Release time
15 Dynamic select VCF, VCA/VCF/VCA/OFF
17 Range 4'/8'/16'
18 PWM LFO/manual
19 Rectangular ON/OFF
20 Sawtooth ON/OFF
21 Sub Level: 0/1/2/3
22 HPF ON/OFF
23 VCF ENV: /\+ \/- (Juno 106 owners know what this is)
24 VCA ENV/GATE
25 CHORUS ON/OFF
26 Noise (Melody) ON/OFF
TABLE 2 - BASS BLOCK PARAMETER
No. Parameter
04 DCO Pulse width
05 VCF Cutoff frequency
06 Resonance
07 ENV Mod
09 Key follow
10 VCA Level
11 ENV Attack time
12 Decay time
13 Sustain time
14 Release time
20 Wave Select Rectangular/Sawtooth
Whole Mode
The MKS-7 has a "Whole Mode". The Melody and Chord sections are combined and act as a six voice synthesizer. In this mode there is no sound from the Melody Section. To turn on the Whole Mode, use the following procedure:
Press the MIDI CH button so the RHYTHM, BASS, CHORD and MELODY buttons are flashing.
While holding the CHORD button, press the MELODY button.
NOTE: The CHORD and MELODY indicators under the LED display should now both be lit.
Press the MIDI CH button to exit.
Entering engineer mode
While holding down one of the sound source selector buttons - MELODY, CHORD or BASS to be edited, depress the midi MIDI CH. The button flashes, indicating the machine is in engineering mode.
Editing
1: Using Tables 1 and 2, find out the number corresponding to a parameter to be altered. Eneter the number on the numerical pad. The display shows the number.
2: DYNAMIC SENS serves as an edit knob, and the new number is represented in the display window as a number between 00 and 127. The numbers above 100 are in lower two digits (eg 123 = 23) In the case where paramters functioning in place of switch, a parameter can effectively open or close the switch when the value exceeds the predetermined figure. For example, CHORUS is turned ON when the value decreases below 63, and OFF when above 64.
Returning to normal mode
Push the MIDI channel button to Normal Functioning.
TABLE 1 - MELODY and CHORD BLOCK PARAMETER
No. Parameter
01 LFO Rate
02 Delay time
03 DCO LFO Modulation
04 PWM
05 VCF Cutoff frequency
06 Resonance
07 ENV Modulation
08 LFO Modulation
09 Key follow
10 VCA Level
11 ENV Attack time
12 Decay time
13 Sustain time
14 Release time
15 Dynamic select VCF, VCA/VCF/VCA/OFF
17 Range 4'/8'/16'
18 PWM LFO/manual
19 Rectangular ON/OFF
20 Sawtooth ON/OFF
21 Sub Level: 0/1/2/3
22 HPF ON/OFF
23 VCF ENV: /\+ \/- (Juno 106 owners know what this is)
24 VCA ENV/GATE
25 CHORUS ON/OFF
26 Noise (Melody) ON/OFF
TABLE 2 - BASS BLOCK PARAMETER
No. Parameter
04 DCO Pulse width
05 VCF Cutoff frequency
06 Resonance
07 ENV Mod
09 Key follow
10 VCA Level
11 ENV Attack time
12 Decay time
13 Sustain time
14 Release time
20 Wave Select Rectangular/Sawtooth
