De Grote Korg MS10 / MS20 / MS50 / SQ10 / MSmini Thread

Het lijkt me wel mooi om er tzt (ooit) nog eens een 2e MS-50 erbij te kopen en het geheel dan in een soort rack in te bouwen boven elkaar bijvoorbeeld.... wel zonder die bakken aan te passen of te beschadigen natuurlijk. Op zich heb je dan al een leuk modulair setje met karakter :W
 

Attachments

  • IMG_0772.jpg
    IMG_0772.jpg
    157,7 KB · Bekeken: 149
Hier nog een stuk uit de Sound on Sound
http://www.soundonsound.com/sos/Oct02/articles/korg40th.asp

If 1977 had been a good year for Keio Electronic's growing reputation, it's fair to say that 1978 was the year in which the company really arrived. It's also fair to say that the MS series of synths and related products launched that year remain some of the most sought-after in the whole world of electronic music.

For those of us who had seen a PS-series synth (and there weren't many), the MS series looked rather familiar, sharing many design features with their forebears, and even sporting the same control-panel hardware. The dual-oscillator MS20 monosynth was the keystone of the range. In addition to its standard controls, this also provided a patchbay that allowed you create new, complex routings to modulate the sounds of the oscillators, filters and amplifier. Although the patchbay did not interrupt the audio signal path, it allowed players to create sounds that were previously the domain of expensive modular and semi-modular instruments.

Its little brother, the MS10, offered just a single oscillator, a single envelope generator, and a shorter keyboard, but it had one thing that the MS20 did not: pulse-width modulation. Then there was the MS50, an expander module that offered numerous additional features provided by neither the MS10 nor the MS20: multiples, an inverter, and patchable ring modulation. Unlike Keio's earlier synths, which used the less common Hertz-per-Volt pitch standard, the MS50 also ran on the Volt-per-octave standard, which meant that you could patch a Korg to the other mainstream synths of the day for the first time. With an MS20, an MS10 and an MS50, the world of monophonic synthesis lay at your feet. Using a handful of cables, you could hook the synths together to create huge patches with four oscillators, multiple filters, multiple envelopes, and multiple modulation sources.

The MS01 was a CV pedal.
The MS02 converted the Hertz-per-Volt pitch CVs of the MS10 and MS20 into the Volt-per-octave systems used by other manufacturers.
The MS03 was in many ways the MS20's External Signal Processor in a box,
and the MS04 was a modulation pedal that provided a multi-waveform LFO and a pedal-controlled CV generator.

The MS series should have been Keio Electronic's big commercial breakthrough, but it is only in the past few years that it has achieved its current status. It was also overshadowed — technically if not in terms of unit sales — by the last of the PS-series polysynths, the wonderful PS3200. This was the first Korg to offer patch memories and, to this day, it remains the only analogue, semi-modular, fully polyphonic, microprocessor-controlled synth.

In common with the PS3100 and PS3300, the 3200 used 'divide-down' oscillators, lacked velocity and pressure sensitivity, and was nowhere near as sleek and transportable as the synths released that year by other manufacturers. But with extensive modulation capabilities, voltage processing, a graphic EQ, a lush Ensemble, far-out sections such as the General Envelope Generator and Adding Amplifier, plus nearly 50 patch points, it offered many more sonic possibilities than the other instruments of the era. Indeed, the PS3200 has a depth and a character that still sets it apart from other instruments, offering a combination of sounds and facilities that remain unique, and in many ways unequalled. Even today, nothing else sounds quite like a PS-series polysynth.

With its knob-festooned control panel, dual oscillators, dual, resonant low-pass and high-pass filters, dual contour generators, and the patchbay that dominated the right of its control panel, the MS20 was a very attractive and powerful synth. In addition, its External Signal Processor provided a comprehensive pitch-to-voltage conversion system and envelope follower that, within limits, enabled external signals to drive the whole of the MS20's architecture.

Perhaps the rarest production synth that Korg ever produced, the MS20 'Blackboard' version (shown here) is electronically identical to the standard MS20, but it is flat, and about four times the size of its common twin. Designed for use as an educational aid, Korg's dealer support staff used this to teach its dealers the principles of synthesis.

Die laatste zijn we al eens in een topic tegengekomen hier op het Synthforum
 
Waarom werkte Korg en Yamaha met Hertz-per-Volt pitch CVs of the MS10 and MS20 in plaats van Volt-per-octave?
Wat zijn/waren de voordelen? Of is het iets in de trend van "Engelsen hebben het stuur rechts?"

Ik kon geen PDF handleiding van die Korg ms02 vinden. http://www.korganalogue.net/korgms/manuals/pp/0201.html

guide to features and functions

Log Amp:
This changes a Hz/V type keyboard CV (control voltage) output into an OCT/V type of CV. Use the Log Amp to change the control signal from a Korg or Yamaha synthesizer into a signal you can use with another type of synthesizer.

Antilog Amp:
This changes an OCT/V type of keyboard CV output into a Hz/V type of CV. Use this Antilog Amp when you want to control a Korg synthesizer by means of a unit that uses the OCT/V system.

Adding Amp:
This can be used for mixing control voltage signals or sound signals.
When not plugged into an outlet, the adding amp operates as if -5V and +5V inputs were connected to its two channels. Therefore, depending on how you set up your equipment, you can also use the adding amp as a voltage supply, or to shift a control voltage to a higher or lower value, and so forth.

Trigger Processor:
This lets you change either type of trigger signals ([ground 1] or [ground 2]) into the kind of trigger signal you need by means of the Reverse switch.


Junctions:
These are additional jacks for simultaneous control of a number of synthesizer units or modules (VCO, VCF, VCA, EG, MG, etc.).
Is dit nou een soort Merge funktie? Die jackingangen zijn niet genummerd. Wel lijkt die reeks onderverdeeld te zijn in 3 gedeeltes. Komen die overeen met de jackingangen daarboven?
 
Bij mij wel in ieder geval :)

MS-10 heb ik niet, maar wel een setje MS-20, MS-50 en SQ-10 en ben daar maar wat blij mee...
Heel mooi! Ik vind zo'n ms50 met die meter (of wat is het) ook erg vet.
 
Waarom werkte Korg en Yamaha met Hertz-per-Volt pitch CVs of the MS10 and MS20 in plaats van Volt-per-octave?
Wat zijn/waren de voordelen? Of is het iets in de trend van "Engelsen hebben het stuur rechts?"

Dit is puur gedaan omdat de Korg een low budget synthesizer moest worden.
Dat scheeld weer een lin/exp converter wat het weer duurder zou maken.
De filter is ook een vrij simpel ontwerp wat wel goed klinkt.
Je kan ook met buizen een ms20 filter vrij simpel na maken.

Maar het volt/hz is gewoon een centen kwestie geweest.
 
Dit is puur gedaan omdat de Korg een low budget synthesizer moest worden.
Dat scheeld weer een lin/exp converter wat het weer duurder zou maken.
De filter is ook een vrij simpel ontwerp wat wel goed klinkt.
Je kan ook met buizen een ms20 filter vrij simpel na maken.

Maar het volt/hz is gewoon een centen kwestie geweest.

Okay thanx. Leuk om te weten!!

Ja wel maf dat de MS20 nieuw 1200 gulden kostte. 1 van de weinige synths die nu 2e hands de nieuwwaarde overstijgt
 
mooi setje hooihuis :okdan:
en idd, 2xms50 naast elkaar met daaronder de ms20 en sq10 :{ :Z :z

Die meter op de MS50 is volgens mij gewoon een Voltmeter om je kabels te tjeken.

Tja, idd, de MS20 is nu duurder dan dat die nieuw was. net zoals de TB :)
 
Heel mooi! Ik vind zo'n ms50 met die meter (of wat is het) ook erg vet.

Is inderdaad een voltmeter op de MS-50, voor zowel DC als AC. Niet zozeer om kabels te checken dus (kan wel) maar meer om te zien wat de modulators uitsturen (inclusief polariteit). Ook van andere modulars eventueel, alleen de meter gaat slechts van -5 tot 5 V.

Al met al best nuttig soms en dus niet alleen voor de looks....

1700 euro is veel te veel voor een MS-50 by the way. "Normale" prijs is zo'n beetje 1100 - 1250 maar wordt door velen nog als te veel gezien. Aan de andere kant, als je alle modules los zou moeten kopen van een andere fabrikant, is het nog niet eens zo gek.
 
Er is toch ook een MS-20 versie met +5/-5 en één met +12/-12 tune voor osc 2? welke is van de eerste serie en welke van de tweede?

Mss kan iem eens een lijst maken van de verschillen tussen beide versies...
 
Klinkt inderdaad leuk, maar niet echt bijzonder, zoiets kan ik ook met m'n Mono/poly maken.
Ik had ook graag iets gehoord wat de full-potentie van de MS50 laat horen.

Het is inderdaad zo dat ik in die track de MS-50 niet heb uitgebuit qua mogelijkheden - de patch kan bijna niet simpeler. Aan de andere kant vraag ik me echt af of de Mono/Poly hetzelfde kan klinken.

Het filter van de MS-50 is namelijk een verhaal apart, reageert echt anders dan bijvoorbeeld van de MS-20 of andere analoge bakken die ik ken. Vooral de resonantie heeft een apart karakter. Dit, samen met in het voorbeeld dan de mogelijkheden van de SQ-10, kan al leuke resultaten opleveren.
 
Het filter van de MS-50 is namelijk een verhaal apart, reageert echt anders dan bijvoorbeeld van de MS-20 of andere analoge bakken die ik ken. Vooral de resonantie heeft een apart karakter. Dit, samen met in het voorbeeld dan de mogelijkheden van de SQ-10, kan al leuke resultaten opleveren.

Kijk dat wou ik weten.
Dank u.
Maarten
 
Het is inderdaad zo dat ik in die track de MS-50 niet heb uitgebuit qua mogelijkheden - de patch kan bijna niet simpeler. Aan de andere kant vraag ik me echt af of de Mono/Poly hetzelfde kan klinken.

Het filter van de MS-50 is namelijk een verhaal apart, reageert echt anders dan bijvoorbeeld van de MS-20 of andere analoge bakken die ik ken. Vooral de resonantie heeft een apart karakter. Dit, samen met in het voorbeeld dan de mogelijkheden van de SQ-10, kan al leuke resultaten opleveren.

Exact hetzelfde zal hij niet klinken maar ik kan binnenkort wel even een stukje mono/poly laten horen wat er toch wel erg op lijkt.
 
8> Klok de SQ10 is met een vco en gebruik een cv output van rij A als audio uitgang.
Je heb nu een digitale achtige golfvorm die je zelf kan "tekenen" met de step knoppen. 8>

Vet!
Dat is nooit in me opgekomen terwijl ik dat met de ARP sequencer ooit WEL gedaan heb.
Binnenkort maar eens ff uitproberen:)
 
Back
Top