Juno 60 met MIDI
- Thread starter N_rco
- Start date
vinnieq
Lidl
- Lid sinds
- 11 juli 2004
- Berichten
- 11.085
Van de website: http://www.engineersatwork.nl/dtronics/datasheets/datasheet_mdbc60.pdf (die je ook zelf had kunnen vinden)
Operating instructions
Setting the midi channel:
• Connect a midi device to the MIDI-IN of the MDCB60, this can be a
keyboard,synthesizer or pc with midi software.
• Hold the button on the MDCB60 and turn on the power of the
JUNO60.
• The LED on the MDCB60 is now on.
• Play a note from the midi device, set on the midi channel you want
to use with the MDCB60.
• The LED on the MDCB60 wil go off and the midi channel is set.
• Note: midi channel for IN and OUT are always the same.
The LED wil flash when the MDCB60 receives midi data on the midi-in
port.
Zo te zien geen controle over MIDI clock, alleen note on/off
Features:
This unit fits inside your JUNO60 and replaces the DCB plug with a MIDI-in and MIDI-out plug.
The MDCB60 converts the Juno DCB signal to a midi signal, So you can use the Juno midi-out to control other midi devices. It only sends out midi-on and midi-off messages.
It also converts midi to DCB, now you can use the Juno as a sound module and play the Juno with your sequencer. It only converts midi-on and midi-off messages, no other things as control messages or program-change and pitch control.
You can select the midi channel (IN and OUT) with a simple push on the button. A LED shows you the midi channel at power-up, the LED shows midi activity on the midi-in port The mdcb60 has a 3mm thick frontpanel and uses metal midi sockets for heavy duty use.
We designed this internal interface as a simple and cheap midi-dcb converter. If you need more features than only playing notes than you should find another (more expensive) midi-dcb converter. This model fits all Juno60 versions
Operating instructions
Setting the midi channel:
• Connect a midi device to the MIDI-IN of the MDCB60, this can be a
keyboard,synthesizer or pc with midi software.
• Hold the button on the MDCB60 and turn on the power of the
JUNO60.
• The LED on the MDCB60 is now on.
• Play a note from the midi device, set on the midi channel you want
to use with the MDCB60.
• The LED on the MDCB60 wil go off and the midi channel is set.
• Note: midi channel for IN and OUT are always the same.
The LED wil flash when the MDCB60 receives midi data on the midi-in
port.
Zo te zien geen controle over MIDI clock, alleen note on/off
Features:
This unit fits inside your JUNO60 and replaces the DCB plug with a MIDI-in and MIDI-out plug.
The MDCB60 converts the Juno DCB signal to a midi signal, So you can use the Juno midi-out to control other midi devices. It only sends out midi-on and midi-off messages.
It also converts midi to DCB, now you can use the Juno as a sound module and play the Juno with your sequencer. It only converts midi-on and midi-off messages, no other things as control messages or program-change and pitch control.
You can select the midi channel (IN and OUT) with a simple push on the button. A LED shows you the midi channel at power-up, the LED shows midi activity on the midi-in port The mdcb60 has a 3mm thick frontpanel and uses metal midi sockets for heavy duty use.
We designed this internal interface as a simple and cheap midi-dcb converter. If you need more features than only playing notes than you should find another (more expensive) midi-dcb converter. This model fits all Juno60 versions
toch bedankt
Als ik de manual zo lees dan zit er geen MIDI thru op. Dat betekent dat je niet door kunt lussen. Dus dit gaat niet werken:
Sequencer -> Juno -> SP
Als de SP wel een thru aansluiting heeft, zou je dus wel om kunnen draaien, dus eerst de SP in de chain.
Sequencer -> Juno -> SP
Als de SP wel een thru aansluiting heeft, zou je dus wel om kunnen draaien, dus eerst de SP in de chain.
